选择和购买: 根据房间大小,选择 4-3/16“ 宽度
Choose the size and profile of the crown modling based on room area and ceiling height.
Size: 4-3/16"
Size: 4-3/16"
选择油漆
Choose type of paint.
Interior Flat is good for the crown molding based on the Home Depot Technician's suggestion.
Interior Flat is good for the crown molding based on the Home Depot Technician's suggestion.
刷漆
切一小块,确定直角边的长度,以后,切割和安装均以来此尺寸。实际测量长度是3英寸。
Cut a small piece of the crown molding;
Put it on the paper with right angle and measure the size as reference.
The real measurement is 3".
Put it on the paper with right angle and measure the size as reference.
The real measurement is 3".
工具: 借朋友的10“miter saw, 买了80齿锯片。
The 10" Miter Saw is little bit small for cutting the 4-3/16" width molding due to the radius is only 5". And also the fence is too low for cutting the molding.
加高后挡板
Make extended fence.
So, 12" miter saw with higher fence is suggested.
So, 12" miter saw with higher fence is suggested.
空气压缩机
Air compressor.
射钉枪和18-2“钉子
Nailer and 18 gauge 2" nails.
根据房间情况,切割成内角左边,内角右边,外角左边和外角右边四种。
Inside comer and outside corner
切割内角左边:移动角度到左侧,将molding 前边面对锯的挡板, 需要的部分在右侧
For cutting Inside corner left piece, the front side of the molding faces to the fence of the saw.
Move the miter to your left side.
Cut.
Keep the right piece.
Move the miter to your left side.
Cut.
Keep the right piece.
切割内角右边:移动角度到右边,将 MOLDING 前面面对锯的挡板,需要的部分在左侧
For cutting Inside corner right piece, the front side of the molding faces to the fence of the saw.
Move the miter to your right side.
Cut.
Keep the left piece.
Move the miter to your right side.
Cut.
Keep the left piece.
切割外角左边:将角度放在右边,molding 背靠锯的挡板,底朝天放置,需要的部分在左侧
For cutting outside corner left piece, the back side of the molding faces to the fence of the saw. And put the molding upside down.
Move the miter to your right side.
Cut.
Keep the left piece.
Move the miter to your right side.
Cut.
Keep the left piece.
切割外角右边:将角度放在左边,将 molding 背靠锯的挡板, 底超天放置,需要的部分在右侧
For cutting outside corner right piece, the back side of the molding faces to the fence of the saw. And put the molding upside down.
Move the miter to your left side.
Cut.
Keep the right piece.
Move the miter to your left side.
Cut.
Keep the right piece.
经验:
将以上的四片放在手边,每次操切割时进行比较,以防切错。
先测量角度,如果角度小于或等于90度,比如A, 将角度值除以2进行切割; 如果角度大于90度, 比如B, 先将该角度除以2,再用90度减。
例如, A= 90, 90/2 = 45, 将miter设置成45度;
例如, B= 140, 1400/2 = 70, 将miter设置成 90-70=20度.
将以上的四片放在手边,每次操切割时进行比较,以防切错。
先测量角度,如果角度小于或等于90度,比如A, 将角度值除以2进行切割; 如果角度大于90度, 比如B, 先将该角度除以2,再用90度减。
例如, A= 90, 90/2 = 45, 将miter设置成45度;
例如, B= 140, 1400/2 = 70, 将miter设置成 90-70=20度.
将气泵输出设置成90PSI, 用射钉枪将切好的MOLDING安装在墙和顶棚之间。开始测量的 3“ 用在这里确定MOLDING 下边距离顶棚的距离。